Go

One of Ben Smeding’s finest twirls in the engine bay, a run-forever 383 crate that makes 460 hp at 5,500 rpm and 460 lb-ft of torque at 4,500 rpm. The motor stands on a nodular iron crank, hypereutectic slugs, and steel connecting rods, has 9.8:1 compression, and ported Edelbrock Performer RPM cylinder heads with Manley 2.02/1.60 valves and COMP springs. The COMP hydraulic roller (234 degrees duration at 0.050, 0.521-inch lift) bumps Scorpion roller rocker arms with COMP swizzle sticks. Much closer to the ground is a Melling high-volume pump and a 5-quart steel sump. The fuel system is founded on an Edelbrock Air-Gap manifold hosting a 750 Speed Demon carburetor drawing through a K&N filter element. Ye old faithful MSD Pro Billet distributor and 6AL box manufacture the zap. Coated Hooker Super Comps extract the brown junk and expel it through a 21/2-inch-diameter Dynomax system. A Bowtie Overdrives 700-R4 provides the vital link as well as an 11-inch converter with a 2,400-stall speed. Tracy Driveline Service built an aluminum prop shaft to ensure the experience. Steve found an F-body 12-bolt that would fit and staffed it with C-clip eliminators, an Eaton Positraction, and 3.73:1 gears.

In

Prior to the soft stuff, Steve rewired the Camaro with a Painless outfit. He installed Dakota Digital instruments and acquired a radio delete plate. To prepare the scene, JD Daniels Auto Upholstery in Stockton, California, installed a field of cut-pile carpeting (including trunk). They restructured the bench to simulate bucket seating and then swathed it and the Corbeau seats with sleek, two-tone black leather. The lap belts are RJS. Steve retained the factory console, outfitted the pedals with some bright billet bits, included electric window lifts, and stuck a Billet Specialties Fast Lane tiller on the tilt steering column. No audio needed.

Out

The body went immediately to rotisserie. Floorpans, rocker panels, and firewall were all in good shape, limiting hard amendments to the rear quarters, light panel, and window filler panel. Steve and Troy also re-skinned the doors and added a ZL2 cowl hood and a somewhat familiar deck spoiler. Before Troy misted it all with PPG two-stage, two-tone silver/charcoal, he coated the underside of the car in gloss black.

Under

We like that Steve’s approach doesn’t mimic the expected and that it’s even a little old school. Before there were completely restructured frames and subframes already outfitted with the right components and infused with specific geometry, you mixed and matched with what the market offered. The OE front subframe was powdercoated to match the body color. From there, it accumulated Global West upper and lower control arms, a QA1 coilover conversion, Hotchkis antisway bar, and an AGR 12:1 power steering box. Competition Engineering frame connectors add torsional stiffness. In the rear, Steve pulled a move retro, retaining the leaf-spring suspension as prescribed by Hotchkis. Axle movement is damped by QA1 adjustable shock absorbers. Before he quit, Steve put another Hotchkis bar in the back.

Unsprung

For nth-degree handling, it is essential to limit unsupported or unsprung weight, e.g., brakes and wheels. The lighter these components, the less spring rate required. Steve bucked the big-brake braggadocio with conservative but balanced Wilwood 12.19-inch diameter rotors and four-piston calipers at all corners of the car. After using them for six years, he still sees no reason to go any larger. Rather than the usual Michelin mondo skins, Steve chose 245/45 and 275/40 BFGoodrich KDW stickies and put them on 18x8 and 18x9.5 Rushforth Whiplash hoops. CHP