|
|
Four-Speed Hurst Shifter InstallGrab A Gear, And Youll Be Shifting Like A Pro In No Time From the February, 2009 issue of Chevy High Performance By Scott Crouse Photography by Jeff Smith
|
|
 Pay close attention to the...  Pay close attention to the way each shift arm is located on the transmission. The arms are designed to angle away from each other to promote shift-rod clearance. Even though these arms will fit several ways on the transmission, there is only one correct way. The rod controls the Third and Fourth gearshift, the longest middle rod controls the First and Second gearshift, and the shortest rod controls Reverse gear.  The Hurst shifter housing...  The Hurst shifter housing uses six bushings, one on each end of the three rods. Hurst offers steel or nylon bushing kits with all the necessary spring clips. Nylon bushings reduce noise and deliver respectable performance. Steel bushings are designed for race applications.  Be sure to install new bushings...  Be sure to install new bushings between the shift arm and shift rod. These bushings are designed to act as a cushion to position the rod.  To prevent binding, its...  To prevent binding, its a good idea to deburr all of the shift arms with a sanding stone.  Once a nylon bushing has been...  Once a nylon bushing has been installed on one side of the shift arm, a special wire clip holds the rod firmly in place. While this factory design works well, it can be improved by adding an AN-style 0.030-inch-thick washer with a 3/8-inch inside diameter...  ...between the arm and ...  ...between the arm and spring.  The shifter must rest in the...  The shifter must rest in the Neutral position during this adjustment. Hurst supplies a 0.250-inch-thick plastic pin to hold the shifter in Neutral. If you dont have one of these tools, try a 1/4-inch drill bit or make your own 1/4-inch steel rod (arrow). With the shifter in Neutral and the shift-rod ends adjusted, the shift-rod ends can be threaded until they slide easily into the shifter. It is best to start with the Reverse rod and work outward. Be sure to work carefully as this will determine how well your shifter works.  Before reinstalling the transmission...  Before reinstalling the transmission back into your car, you must adjust the shifter stops. The First and Third gear stop is located on the back of the shifter tower (A). The Second and Fourth gear stop is on the front of the tower (B).  If you have a used Hurst shifter...  If you have a used Hurst shifter and dont know how it bolts to your transmission, you can log onto www.mrgasket.com and find out. Go to the Hurst section of the site, find your application, and print out the installation instructions. This saves hours of trying to figure out how all those arms and levers connect. Imagine watching a stoplight turn green and dropping the clutch to pull ahead of the car next to you. As the revs climb, you depress the clutch and grab Second gear. The shifter feels sloppy, and you find yourself searching for a gearany gear. Its frustrating and could even be dangerous if you had to get out of the way of a runaway cement truck. Theres little point to having a performance car if you cant find the gear you want, when you want it. If youve ever experienced this problem, its time for a new shifter. The feeling of being pinned in your seat while blasting gears is second to none. Companies such as Richmond, Tremec, and Borg Warner offer stout gearboxes, but the grandfather of the GM performance manual trans lineage has to be the Muncie four-speed. Over the years, this quality four-speed box backed both big- and small-blocks. The same praise cannot be lavished on the Muncie shifter. Frankly, it was abysmal. If you are looking to help out your Muncie four-speed, the Hurst Competition-Plus shifter is the way to go. Its carefully constructed design promotes a positive feel with gear-grabbing precision. Follow along as we show you how to set one up and tune it. Youll be shifting like a pro in no time.
|
Hurst Shifter Rebuild Service
Carson City
NV
89701-537
|
Hurst/Mr. Gasket
Cleveland
OH
44144
|
|
|
|
Express Mouse
Regular CHP readers may recognize Larry Richards as that guy who has been top-speed racing in...
more
|
|
|
In the Clutch
The clutch comes out, and the Camaro launches hard. The tach hits 6,000 rpm and you stab the clutch...
more
|
|
|
The Sub Way
Perhaps the most sought-after car in the Chevy musclecar lineup is the early Camaro. While this...
more
|
|
|
Agent 87, Part I
In the February, 2001 issue, we brought you the 411 HP on 87 Octane story. This was...
more
|
|
|
|
|
|
Timing Is Everything
Theres a proper time for everything. Driving through an intersection just a little too soon...
more
|
|
|
Low-Dollar Paint
Looking for a major image upgrade? Nothing impacts the street crowd more than a fresh new paint...
more
|
|
|
|
|
|
Header Bolt-On Tricks
As with any project, there's a right way and a wrong way to install headers. CHP talked to header...
more
|
|
|
Dialing It In
A properly tuned engine and suspension are key to keeping your Chevy running hard. Monitoring that...
more
|
|