Swapping in a new HEI, or even just pulling one out to service, is quite simple. All it requires is basic handtools and some background info on how the distributor works in conjunction with the engine. Small slipups here could require major troubleshooting later to figure out why the engine won't idle properly and why power lags. It's easy to understand why so many do-it-yourselfers get frustrated when trying an install for the first time-many small items cannot be overlooked. Things like engine-timing position and distributor shaft position all play a role in the function of the distributor, and if they're not given proper attention, the distributor will not fall into place.

HEIs have a too-good-to-be-true reputation. Plop one in and you're set, which makes them the perfect way of dispersing spark among your eight cylinders. However, like many engine components, parts do wear out, and when they do it's time to replace them. Our case here is a perfect example. This big-block was nothing special; it provided everyday grunt with iron heads, 2-inch headers, and a Holley 750 carburetor. But its old HEI unit couldn't be timed correctly because of a worn-out shaft. It was time to swap in a new unit from Davis Unified Ignition (DUI). The best part is these gems from DUI can be custom-tuned to your application, which only takes a quick phone call to Davis-have your engine specs ready.

We got this big-block running in about an hour, but first-timers may take a bit longer and having help speeds things up as well. As you can see from these step-by-step instructions, replacing your old unit with a fresh Davis Unified Ignition HEI is almost too simple. Just watch out for those pitfalls.

Quick Notes
What We Did
Pulled out the old HEI and swapped in a brand-new unit from DUI (PN 12720)

Bottom Line
It won't take long to get that big-block correctly timed and running sweet

Cost (APPROX)
$250

  • Chevy Big Block Distributor Swap 1980Chevy El Camino
    Joe Rubio is no rookie when it comes to working on his favorite El Camino. He frequently wrenches on it at his auto body shop, which is also where our Project Brutus is getting all its bodywork done. After popping the hood on the '80 El Camino we needed to land the engine at top dead center (TDC). Since the big-block is in the engine bay, all we had to do was bump the ignition with the key until the timing pointer marks matched up with the front balancer. To double-check, we also pulled the No. 1 spark plug and plugged the hole with a finger. As the motor comes to TDC, the compression will push your finger out.
    Joe Rubio is no rookie when it comes to working on his favorite El Camino. He frequently w
  • Chevy Big Block Distributor Swap Stock Gm Hei Distributor
    From there, we began to remove anything that would slow us down. Rubio disconnected vacuum lines and the throttle cables. This would leave us a clear path to remove the old stock GM HEI.
    From there, we began to remove anything that would slow us down. Rubio disconnected vacuum
  • Chevy Big Block Distributor Swap Spark Plugs
    We went through and disconnected all the spark plug looms and wires. Then, using a long Phillips screwdriver, we removed the cap
    We went through and disconnected all the spark plug looms and wires. Then, using a long Ph
  • Chevy Big Block Distributor Swap Ignition Wiring
    To get the old distributor out of the hole, we used a 9/16-inch open wrench to remove the clamp, then we disconnected the ignition wiring. Rubio then pulled the distributor straight up and out of the engine. We took special note of the position of the rotor. The new HEI needs to fall into place just as the old one did.
    To get the old distributor out of the hole, we used a 9/16-inch open wrench to remove the
  • Chevy Big Block Distributor Swap Davis Unified Ignition
    To get the new distributor ready, we pulled the new cap off the Davis Unified Ignition (DUI) unit using the same Phillips screwdriver. We turned the rotor and shaft to match the same position as the old HEI.
    To get the new distributor ready, we pulled the new cap off the Davis Unified Ignition (DU
  • Chevy Big Block Distributor Swap Distributor Gasket
    Distributor gaskets can be reused. Since ours wasn't torn, we simply placed ours onto the shaft.
    Distributor gaskets can be reused. Since ours wasn't torn, we simply placed ours onto the
  • Chevy Big Block Distributor Swap Camshaft Gears
    Rubio tucked himself under the hood and dropped in the new HEI unit. It took some patience and finesse turning the rotor, but eventually the distributor shaft gears meshed with the cam gear inside the block. It fell right in at the same location as the old unit.
    Rubio tucked himself under the hood and dropped in the new HEI unit. It took some patience
  • Chevy Big Block Distributor Swap Silicone Jacket
    Once the distributor had positive engagement and sat flush against the manifold, we began to close up all the loose ends. Rubio landed the cap atop the rotor and used the Phillips screwdriver to secure it. DUI Live Wires (PN C9053, $100) come with easy-to-read cylinder numbers on each end, which made finding their places a cinch. Live Wires are also heat-resistant and have a durable, long-lasting silicone jacket and insulation. Spiral-wound cores prevent electronic interference. Following the standard big-block firing order (1-8-4-3-6-5-7-2), we plugged in the wires to the top of the rotor and then to the spark plugs.
    Once the distributor had positive engagement and sat flush against the manifold, we began
  • Chevy Big Block Distributor Swap Ignition Power
    We left the clamp on the distributor just snug, but tight enough so it wouldn't jump around. From there, we followed through and hooked up all the necessary vacuum lines, throttle cable, and power to the ignition. However, we did leave the vacuum line to the vacuum advance diaphragm disconnected until we timed the engine.
    We left the clamp on the distributor just snug, but tight enough so it wouldn't jump aroun
  • Chevy Big Block Distributor Swap Burnouts
    Rubio installed the air cleaner, stabbed the throttle for fuel, and turned the key. At first it didn't start, so we advanced the distributor a bit by turning it toward the carburetor. Once she fired up, Rubio went ahead and readjusted the idle. From there we ran the timing gun and advanced the timing to 36 degrees, where it ran smooth. After an impressive testdrive he said he could add another 100 feet to his burnouts.
    Rubio installed the air cleaner, stabbed the throttle for fuel, and turned the key. At fir
  • Chevy Big Block Distributor Swap Matanence Free
    The old (right) and new (left) distributors are almost identical. What sets them apart is Davis' knack for creating custom-calibrated units for your particular application. Even light throttle ping is eliminated by using DUI's special vacuum advances, making the units virtually maintenance-free. We got our cap in black, but they also come in blue, red, yellow, and clear. Ours also came with solid brass terminals and the DUI coil and Dyna-Module. The module provides more "electric dwell," which allows the coil to produce a more intense spark.
    The old (right) and new (left) distributors are almost identical. What sets them apart is
SOURCE
Davis Unified Ignition
performancedistributors.com
See all 12 Photos