Solid Roller Reliability

Many years ago, solid roller cams were perceived to be unreliable for extended street use, but several changes have been implemented in recent years to improve oiling and extend lifter longevity. Several years back, we noticed that bracket racers were putting more time on roller lifters with fewer failures than the guys who only drove their cars once a week to the burger stand for cruise night. The main difference in the two engines is that the cruise night engine rarely sees high rpm, but in a bracket motor there is often more oil getting thrown around all over the engine from windage. With that in mind, we began developing lifters with improved oiling for the needle bearings. The culmination of that technology is in COMP Cam's Elite Race lifters with pressurized tool steel axle. These lifters feature pressurized oil inlets that deliver oil through the axles and directly to the needle bearings.

Modern Oil and Flat-Tappet Wear

In modern motor oils, many of the additives necessary for reliable flat-tappet cam performance have been removed. We try never to get tied up in environmental debates, but the EPA did place severe limits to the amount of zinc phosphates allowed on any road use oils because they believed those chemicals might get past the rings and damage the catalytic converters. The oil industry fought back because these ZDDPs are very inexpensive and effective soldiers that sacrifice themselves instead of the wear surfaces under high loads, such as those seen in flat-tappet cam applications. The EPA won, despite the fact that the industry would have preferred some more testing on the stability of different zinc phosphate combinations. We always recommend using either oils developed specifically for flat-tappet lifters or using special additive packages when running flat-tappet cams. Since not too many people have a stash of late '90s Rotella motor oil in their garage, COMP Cams offers a range of oils and additive solutions, and there are other good products on the market, such as those from Joe Gibbs Racing. At COMP Cams, we never really wanted to get in the oil business, but we had to get in to keep the cam failures to a minimum. COMP Cams' Hot Rod Oil and Joe Gibbs Racing Oil are excellent solutions for providing the protection that flat-tappet motors need. Another alternative is adding a bottle of COMP's "159" break-in additive to any off-the-shelf motor oil.

Offset Lifters

Some cylinder heads require offset lifters to kick the pushrod over to the side in an effort to optimize port geometry. That means that the pushrod is not centered on lifter body as it is with a traditional lifter. While this does affect valvetrain stability and wear, it's not as much as you might think. Anything under a 2-degree angle does not reduce stability. Past that point, it's safe to assume that every additional 2 degrees takes stiffness out of the pushrod equivalent to reducing the pushrod diameter by roughly 1/16 inch or more. The offset does not harm the stiffness, but does increase the wear on both the cam and lift as it tries to twist the lifter in the bore. How much wear is increased depends on the amount of load placed on the system.

Lifter Preload

As basic as it may seem, not everyone agrees on how to set the preload with a hydraulic cam. Many engine builders refer to this preload as "turns past zero lash". In production engines, manufacturers set the lifter near the middle of its travel. We have done considerable testing and with anywhere from approximately one turn from the top to one turn from the bottom, the valvetrain system behaves very consistently. Performance engine builders tend to fall into one of two schools of thought. Running light preload-zero to half a turn-allows the system to recover quickly if you go through an instability region. This is because the hydraulic system can try to hold the valve open after any bounce of more than a few thousandths of an inch. With solid lifters, the shape of valve bounce is a classic parabolic motion with symmetrical up and down patterns. With hydraulic lifters, the valve bounces off the seat and can then close very slowly on the way down, as the hydraulic system tries to take up the newfound clearance. To keep the system from hanging the valve open, some racers run minimum preload. On the other hand, the less preload you run, the more oil volume you have under the piston. The greater volume also means you have more aeration, or tiny oil bubbles in suspension, under the piston that can compress. Hence, some engine builders like to set the lifters from the bottom up, perhaps half a turn from the bottom, while using a longer pushrod to maintain good geometry. Clearly the first method allows the engine to go through mild "bad spots" better and the second method helps improve overall stability. The beauty of a short-travel lifter is that it allows the engine builder to choose both options and take advantage of the best of both worlds.

Lifter Materials

The materials used to manufacture lifters have evolved over the years, and directly contribute to increased durability. Most mechanical lifters are made from very high-grade cast iron that has values of 55 or greater on the Rockwell hardness scale. Tool steel lifters are also becoming quite common. They can be used on cast-iron cams without coatings if the cam is either nitrided or super finished. On steel cams, the lifter foot requires a special DLC coating to prevent micro-welding between the mating parts. Beware that of the 100-plus companies that say they can DLC coat lifters, only about three have DLC recipes that will live with the impacts common to the tappet face in performance engines without flaking or wearing prematurely.

Roller Durability

In a high-rpm race motor with big valves and lots of spring pressure, the roller assembly in a solid-roller cam takes a lot of abuse. To enhance durability, several features can be incorporated into a lifter's design. Larger axles are pretty much a must, as the needles contact the axle at approximately the same angle every time on the opening side, as the valve opens and applies roughly 3,000 pounds of force for a few milliseconds. This will result in spalling of the axle unless the forces can be well distributed. For the same reason, more needles help spread the load between needles more evenly. With a larger axle, the wheel will become thinner unless you go to a larger outside diameter wheel. Using great materials in all three components is paramount. At the same time, direct oiling reduces surface temperature and scrubbing friction. We certainly prefer a 0.904-inch outside diameter COMP Cams Elite lifter with a 0.820-inch wheel over the 0.842-inch outside diameter lifter with a 0.755-inch outside diameter wheel when a customer can fit the larger body in the block.

Rebuildable Lifters

The cost of replacing lifters every season in a race motor can get expensive, so at COMP Cams we developed our Endure-X lifters with rebuilds in mind. Typically, most bracket racers will replace lifters about twice a season. During the rebuild process, we replace high-wear items like the axle, needles, and wheel. Since the lifter bodies also incur wear during race use, I would not recommend more than one or maybe two rebuilds. Now that the wheels, needles, and axles are so much better than even five or ten years ago, by the time you get to the second rebuild the body would really need to be replaced as well as the rolling assembly.

SOURCE
Comp Cams
3406 Democrat Rd
Memphis
TN  38118
800-999-0853
www.compcams.com